Motorcycle Audio Amplifiers

The PBR300X2 is a 300 Watt amplifier with Boosted Rail Technology, allowing it to be compact and efficient while providing big power. This amp is great for smaller stealth installations, motorcycles and recreational vehicles.

•12dB/octave Butterworth crossover
•MOSFET output stage
•High level inputs
•Ultra compact chassis
•Variable 4-6 volt hi level DC offset voltage input turn-on control
•1 Year Standard Warranty

PBR300X2
The Punch PBR300X2 uses our patented BRT (Boosted Rail Technology) for an ultra efficient design that does not use a switching power supply to generate its rated power. This allows the chassis design to be much smaller than traditional sized amplifiers. The BRT also has a variable hi-level DC offset turn-on circuit for easy installation into any OEM system. It is great for smaller stealth installations, as well as for motorcycles and recreational vehicles.

CEA-2006 Compliant:

Number of Channels: 2

Rated Power
(RMS Continuous Power):

100 Watts x 2 @ 4-Ohm
150 Watts x 2 @ 2-Ohm
300 Watts x 1 @ 4-Ohm Bridged

Total Power
(Sum of Rated Power): 300 Watts

Dynamic Power
(PVC/PowerCube® Measurement):

Bridgeable: YES

Efficiency (average):

Crossover Controls:

High-Pass: 50Hz - 500Hz @ 12dB/Octave Butterworth
Low-Pass: 50Hz - 500Hz @ 12dB/Octave Butterwort

Tone Controls:

Signal Input: High/Low Level Input: 4-Pin harness, Hi-Level Sensitivity: Variable DC offset sensitivity

Signal Output: NA

Power Input Connector: Block Harness

Power Wire Gauge: 10 AWG

Speaker Output Connector: 4 Pin Harness

Speaker Wire Gauge: Harness 12 AWG

Heat Sink Type: Extruded Aluminum

Cooling: Convection

Remote Controls:
Optional PEQ provides 0dB to +18dB @ 45Hz

Visual Indicators:Power/Protect, BRT (Boost)

Circuit Topology Class: Class-BR

Frequency Response: 20Hz-20kHz +/-3dB

Shipping Weight: 2.8 Lbs. (1.27 Kg.)

Dimensions (HxWxL): 1.53" x 4.25" x 6.75"
(3.90cm x 10.8cm x 17.2cm)

SPECIFICATIONS

This Amplifier is great to use when installing a radio or any audio device which supplies a High Audio output, most amplifiers require you to use a low audio input or use a high to low audio converter to make a Car Radio, or any other device that can supply enough sound for a pair of external speakers work without distortion. All I can say is this is a very high quality item and I am proud to make it available to my customers it cranks out 300 Watts of pure power, and comes with a one year manufacturers Warranty

•Remote wired bass/treble boost
•0dB to +18dB bass boost @ 45Hz.
•0dB to +12dB treble boost with hinge filter between 1kHz to 20kHz.
•Includes remote knob, cable, mounting clip, mounting screws
•Designed for 2007+ newer compatible amplifiers
•Bass/Treble filtering based upon in-board amplifier crossover setting (HP-LP-AP)
•1 Year Standard Warranty

This remote Punch EQ offers 0dB to +18dB boost @ 45Hz and/or a hinge treble boost 0dB to +12dB @ 12kHz. Cable and mounting hardware included. For use with compact 2007 and newer PUNCH & POWER amplifiers.

Remote Tone Equilizer ( PEQ )

Punch EQ2
U.S. Patent 3,883,832
Onboard equalizer with up to +18dB @ 45Hz and/or up to +12dB boost at 12kHz.

In the early 70's, Jim Fosgate studied the acoustical properties of automobiles. Utilizing a real-time analyzer and pink noise, he would graph out the acoustical characteristics of each car he tested. Jim discovered three problems that were common to all cars:
•A midbass hump between 100-275Hz
•A steep roll-off of high frequencies from 2kHz up to 20kHz
•Reduced bass response below 50Hz
The Punch EQ on-board equalization circuit helps correct for these acoustical deficiencies in the listening environment. When set to Low-Pass(LP) operation, it becomes a variable Bass Boost. When set to High-Pass (HP) operation, it acts as a variable Mid-Bass and Treble Boost. When set to All Pass (AP) operation, both Bass and Treble frequencies are boosted.

300 Watts of pure power avilable with a tone control to bring out your High Treble sound or your low Bass sound

Quality at it's Best!